XDS110 is currently available in both standalone or embedded versions. ARM9 based processors that use (emu_adaptive_clocking.html) such as OMAPL13x, AM1xxx, DM64xx Other TI SoCs with PRU, C674x, C66xx, Cortex M, Cortex R and Cortex A cores 66AK2 and TCI66x Multicore DSP + ARM® SoCs (Keystone II) C674x and C66x (Keystone I) Floating point DSPs mmWave sensors (IWR/AWR14xx, IWR/AWR16xx, IWR68xx) Automotive SoCs (TDAx ADAS, DRAx infotainment) C2000, TM4C12x and Hercules microcontrollers SimpleLink MCUs (CC13xx, CC26xx, CC3x, MSP432) OpenOCD ready (OpenOCD version 0.8 and above). Interface compliant with currently published XDS APIs and CMSIS-DAP. Expansion header for the EnergyTrace HDR accessory (TMDSEMU110-ETH) for wider dynamic range up to 800mA. Built-in EnergyTrace technology for precise measurements of up to 75mA. Target power-loss detection via the TVRef pin. #Max utilities serial number full#Host interface: USB2.0 Full Speed (11Mbps) or High Speed (480Mbps). #Max utilities serial number manual#For more information on the trace capabilities of a particular device please refer to its technical reference manual (TRM) Core and System trace are available via the ETB in selected ARM and DSP processors Serial Wire Output (SWO) are available for selected microcontrollers and wireless connectivity microcontrollers Real-Time Mode in selected microcontrollers and DSPs. #Max utilities serial number software#Software and Hardware Breakpoint support Emulation Connect/Disconnect, Read/Write memory, Read registers, Load program, Run, Halt, Step Protocols: IEEE1149.1 (JTAG), IEEE1149.7 (cJTAG) as well as ARM's Serial Wire Debug (SWD) and Serial Wire Output (SWO). The standalone XDS110 Debug probe (TMDSEMU110-U) requires CCS version 7.0.0 or newer. #Max utilities serial number code#As an added flexibility, the same physical connection for EnergyTrace also features one UART port and four GPIOs for total hardware control.Įmbedded (on-board) XDS110 debug probes are compatible with Code Composer Studio (CCS) development environment version 6.1.0 and newer. EnergyTrace is a technology that allows measuring the true Energy and Power consumption of the target board and it can measure up to 75mA natively and up to 800mA with the add-on module. The XDS110 is also the first of the XDS family of debug probes to feature (emu_energytrace.html) and its add-on module EnergyTrace HDR for Simplelink microcontrollers. In addition to that, all variants feature modular target configuration adapters for TI and ARM standard JTAG headers (the offer of adapters varies per model). Also, both Core Processor and System Trace are available for all ARM and DSP devices that support Embedded Trace Buffer (ETB).įollowing the trend for space reduction on modern TI development boards, the XDS110 features a standard TI 20-pin connector as the primary JTAG connectivity to the target. The XDS110 replaces the XDS100 technology and is the first debug probe that supports all TI devices with JTAG, cJTAG and SWD/SWO debug port in a single product. Designed to be a complete solution that delivers JTAG and SWD connectivity at a low cost, the XDS110 is the debug probe of choice for entry-level debugging of TI microcontrollers, processors and SimpleLink devices. The XDS110 is the latest entry level debug probe (emulators) for TI embedded processors. See additional products at the section below (#which-xds110-is-right-for-me-) Contains ordering information, availability, compliance data.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |